1800 Q&As in UPDATED 200-301 Exam Questions Certification Test Engine to PDF
Get The Important Preparation Guide With 200-301 Dumps
To prepare for the Cisco 200-301 certification exam, candidates can take instructor-led training courses, self-paced online courses, virtual labs, and practice exams. Cisco recommends that candidates have at least one year of networking experience before taking the exam. Candidates can also join the Cisco Learning Network, a community of IT professionals who share knowledge and resources related to Cisco technologies and certifications.
NEW QUESTION # 463
Refer to the exhibit.
The New York router is configured with static routes pointing to the Atlanta and Washington sites. Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another?
(Choose two.)
- A. Configure the ipv6 route 2012::/126 2023::1 command on the Washington router.
- B. Configure the Ipv6 route 2012::/126 s0/0/0 command on the Atlanta router.
- C. Configure the ipv6 route 2012::/126 2023::2 command on the Washington router.
- D. Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta router.
- E. Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router.
Answer: C,E
Explanation:
The short syntax of static IPv6 route is:
ipv6 route <destination-IPv6-address> {next-hop-IPv6-address | exit-interface}
NEW QUESTION # 464
Drag and drop the descriptions from the left onto the configuration-management technologies on the right.
Answer:
Explanation:
NEW QUESTION # 465
Refer to the exhibit.
When PC-A sends traffic to PC-B, which network component is in charge of receiving the packet from PC-A verifying the IP addresses, and forwarding the packet to PC-B?
- A. Router
- B. Layer 2 switch
- C. firewall
- D. Load balancer
Answer: A
NEW QUESTION # 466
When is the most appropriate time to escalate an issue that you are troubleshooting?
- A. when a more urgent issue that requires your intervention is detected
- B. when you have gathered all available information about the issue
- C. when you have been unable to resolve the issue after 30 minutes
- D. when you lack proper resources to resolve the issue
Answer: D
Explanation:
This is the key reason to escalate. If you do not have the necessary tools, permissions, knowledge, or authority to fix the problem, escalating ensures the issue is handled by someone who can resolve it efficiently.
NEW QUESTION # 467
Refer to the exhibit.
Which password must an engineer use to enter the enable mode?
- A. default
- B. cisco123
- C. adminadmin123
- D. testing 1234
Answer: D
Explanation:
Explanation
If neither the enable password command nor the enable secret command is configured, and if there is a line password configured for the console, the console line password serves as the enable password for all VTY sessions -> The "enable secret" will be used first if available, then "enable password" and line password.
NEW QUESTION # 468
What is a function of a northbound API in an SDN environment?
- A. It upgrades software and restores files.
- B. It provides orchestration and network automation services.
- C. It supports distributed processing for configuration.
- D. It relies on global provisioning and configuration.
Answer: B
NEW QUESTION # 469
Refer to the exhibit.
Which action do the switches take on the trunk link?
- A. The trunk forms, but VLAN 99 and VLAN 999 are in a shutdown state.
- B. The trunk does not form, but VLAN 99 and VLAN 999 are allowed to traverse the link.
- C. The trunk forms, but the mismatched native VLANs are merged into a single broadcast domain.
- D. The trunk does not form, and the ports go into an err-disabled status.
Answer: C
NEW QUESTION # 470
Refer to the exhibit.
SW_1 and SW_12 represent two companies that are merging. They use separate network vendors. The VLANs on both Sides have been migrated to share IP subnets. Which command sequence must be issued on both sides to join the two companies and pass all VLANs between the companies?
- A. switchport dynamic autoswitchport nonegotiate
- B. switchport mode dynamic desirableswitchport trunk allowed vlan allswitchport trunk native vlan 7
- C. switchport mode trunkswitchport trunk allowed vlan allswitchport dot1q ethertype 0800
- D. switchport mode trunkswitchport trunk encapsulation dot1q
Answer: D
NEW QUESTION # 471
Drag and drop the characteristic from the left onto the IPv6 address type on the right.
Answer:
Explanation:
Explanation:
NEW QUESTION # 472
Refer to the exhibit.
What is the effect of this configuration?
- A. Dynamic ARP inspection is disabled because the ARP ACL is missing
- B. The switch port interface trust state becomes untrusted
- C. The switch port remains down until it is configured to trust or untrust incoming packets
- D. The switch port remains administratively down until the interface is connected to another switch
Answer: B
Explanation:
Explanation
Dynamic ARP inspection (DAI) is a security feature that validates ARP packets in a network. It intercepts, logs, and discards ARP packets with invalid IP-to-MAC address bindings. This capability protects the network from certain man-in-the-middle attacks. After enabling DAI, all ports become untrusted ports.
NEW QUESTION # 473
A network engineer is configuring an OSPFv2 neighbor adjacency Drag and drop the parameters from the left onto their required categories on the right. Not all parameters are used
Answer:
Explanation:
NEW QUESTION # 474
Refer to the exhibit.
Which plan must be Implemented to ensure optimal QoS marking practices on this network?
- A. As traffic traverses MLS1 remark the traffic, but trust all markings at the access layer.
- B. As traffic enters from the access layer on SW1 and SW2. trust all traffic markings.
- C. Remark traffic as it traverses R1 and trust all markings at the access layer.
- D. Trust the IP phone markings on SW1 and mark traffic entering SW2 at SW2.
Answer: C
NEW QUESTION # 475
Refer to the exhibit.
If R1 receives a packet destined to 172.161.1, to which IP address does it send the packet?
- A. 192.168.15.5
- B. 192.168.13.3
- C. 192.168.14.4
- D. 192.168.12.2
Answer: C
NEW QUESTION # 476
Refer to Exhibit.
Which configuration must be applied to the router that configures PAT to translate all addresses in VLAN 200 while allowing devices on VLAN 100 to use their own IP addresses?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION # 477
Refer to the exhibit.
Which switch in this configuration will be elected as the root bridge?
- A. SW2
- B. SW1
- C. SW4
- D. SW3
Answer: B
NEW QUESTION # 478
An engineer must configure a/30 subnet between two routers. Which usable IP address and subnet mask combination meets this criteria?
- A. Option D
- B. Option A
- C. Option B
- D. Option C
Answer: B
NEW QUESTION # 479
Refer to the exhibit. A network engineer must configure R1 so that it sends all packets destined to the 10.0.0.0/24 network to R3, and all packets destined to PC1 to R2. Which configuration must the engineer implement?
- A. R1(config)#ip route 10.0.0.0 255.255.0.0 172.16.0.2
R1(config)#ip route 10.0.0.5 255.255.255.255 192.168.0.2 - B. R1(config)#ip route 10.0.0.0 255.255.255.0 192.168.0.2
R1(config)#ip route 10.0.0.5 255.255.255.255 172.16.0.2 - C. R1(config)#ip route 10.0.0.0 255.255.0.0 192.168.0.2
R1(config)#ip route 10.0.0.5 255.255.255.0 172.16.0.2 - D. R1(config)#ip route 10.0.0.0 255.255.255.0 172.16.0.2
R1(config)#ip route 10.0.0.5 255.255.255.255 192.168.0.2
Answer: B
NEW QUESTION # 480
......
Prepare With Top Rated High-quality 200-301 Dumps For Success in Exam: https://testinsides.vcedumps.com/200-301-examcollection.html
